These are the steps I took to get the SunRay software working on Centos. I was able to get this working thanks to scraps of information from Peter Senna Tschudin's blog In addition to get it working on 32bit like in Peter's blog, I also got it working on 64 bit. These are the instructions for 64bit.
The SunRays we have are the SunRay 2 model updated with the latest firmware.
Download the software from Oracle's support portal (requires login)
# download files from Oracle's website
Install the dependencies
yum install glib dhcp openldap-clients tftp-server libXp libXfont.i386 openmotif22 openssl compat-libstdc++-33 libusb-devel compat-openldap kernel-devel gdbm.i386 gcc openmotif.i386 sssd-client.i386
If you are not using sssd you will need to install the nscd.i386 package.
Install the firmware
Installing Sun Ray Operating Software 184.108.40.206
Sun Ray Operating Software 220.127.116.11 has been successfully installed.
This output has been logged to
Install the bundled JRE and Apache Tomcat
mv jre1.6.0_41/ /opt/
tar xvf apache-tomcat-5.5.36.tar
mv apache-tomcat-5.5.36 /opt/
ln -s /opt/apache-tomcat-5.5.36/ /opt/apache-tomcat
Install the Sunray Server Software
Accept? (Y/N) y
Enter Java v1.6 (or later) location: [/usr/java] /opt/jre1.6.0_41/
Continue? (Y/N) [Y] y
Enter new UT admin password:
Again: Enter new UT admin password:
Configure Sun Ray Web Administration? (Y/N) [N] y
Enter Apache Tomcat installation directory [/opt/apache-tomcat]
Enter HTTP port number  8080
Enable secure connections? (Y/N) [Y] y
Enter HTTPS port number  8081
Enter Tomcat process username [utwww]
Enable remote server administration? (Y/N) [N] Y
Configure Sun Ray Kiosk Mode? (Y/N) [N] N
Configure this server for a failover group? (Y/N) [N]
About to configure the following software products:
Sun Ray Data Store 3.5
Sun Ray root entry: o=utdata
Sun Ray root name: utdata
Sun Ray utdata admin password: (not shown)
SRDS 'rootdn': cn=admin,o=utdata
Sun Ray Web Administration hosted at Apache Tomcat/5.5.36
Apache Tomcat installation directory: /opt/apache-tomcat
HTTP port number: 8080
HTTPS port number: 8081
Tomcat process username: utwww
Remote server administration: Enabled
Sun Ray Server Software 4.5
Failover group: no
Sun Ray Kiosk Mode: no
Continue? (Y/N) [Y]
Enter groupname for Windows Connector [utwc]
Enter group ID (gid) for the group [auto]
Do you want to configure Firmware downloads for Sun Ray clients? (Y/N) [Y]
Seriously you should reboot
If the services are not running on reboot
You can manually start them with:
/opt/SUNWut/sbin/utadm -L on
SunRay Web Administration
Log into https://mysunrayserver.example.org:8081
With the user: admin and the password you specified in the installer.
Note: Replace port 8081 with the port you selected in the installer if you did not select 8081.
If you can't log in because the "data store is not responding" proceed to the debugging section.
- Click "Advanced"
- Check all the encryption buttons
- Switch soft to hard for client and server
- Following instruction to restart client
The following two log files were especially helpful in debugging problems.
tail -f /var/opt/SUNWut/log/messages
tail -f /var/log/autholog
We have the SunRays in there own vlan and only the SunRay servers are allowed to communicate with them. You should also firewall the Web Admin ports in my case port 8080 and 8081.
I havn't had a lot of luck with a consistent installation using the instructions above. If it doesn't work the first time try uninstalling and resintalling the SunRay software. Also I was doing this with SELinux disabled and we already had working SunRays with Solaris 10 so I can't really comment on the dhcp configs or any special network acls we may have in place.